This article was posted 12/18/2008 and is most likely outdated.

How to Properly Construct a Ground System
 

 

Topic - Lightning/Surge Protection
Subject - How to Properly Construct a Ground System

December 18, 2008
This newsletter was sent to 30650 newsletter subscribers

Ask a Question |  Weekly Code GraphicQuizzes |  Free Stuff InstructorsOnline Training Products | Seminars | SubscribeUnsubscribe
[ image1 Post Comments | View Comments | Notify Me When Comments Are Added ] Web Page Version [Printer-Friendly]    

How to Properly Construct a Ground System

 

The failure to properly bond radio station equipment and associated antenna grounding systems to the AC entrance grounding electrode is a leading cause of damage to radio equipment, notably in amateur radio installations. The source of such damage from a lightning attachment most often occurs when the strike is to power company or telecommunication equipment. Lightning energy enters the structure on the power company system and exits via communication devices and their coaxial feed lines to an isolated grounding system. Had the system been properly bonded in accordance with codes and standards cited below, there would have been an equipotential condition maintained that would serve to limit such current equalizations at the expense of solid state equipment in it's path.

 

NEC (US National Electrical Code) article 250 (grounding), article 810 (Radio and Television Equipment), and NFPA 780 (Standard for the Installation of Lightning Protection Systems) are all clear on the absolute requirement to bond all grounding systems to the AC service entrance grounding electrode.

 

Surge protection for a coaxial feed line (center conductor) to the radio station can be accomplished by either installing a coaxial surge protector device, or by isolation via fiber optic or high voltage isolation transformers.  However all coaxial shield grounds, antenna mast grounds and the structure AC entrance ground must be bonded for lightning protection safety.

 

Ground-loops that cause impedance imbalances (audio-hum) for audio-visual equipment often tempts installers to isolate these systems from the building ground.  The source of the problem can usually be traced to daisy-chaining ground (bonding) straps or improperly functioning equipment elsewhere in the structure.  It is no favor to the equipment owner for an installer to take short cuts in lightning protection in order to correct an audio-hum issue, the cause of which is not from proper bonding and grounding.

 

Respectfully,

Jack Painter

5th CG District Communications Staff Officer

U.S. Coast Guard Auxiliary Virginia Beach VA

 

This information was originally posted on the LightningProtection Yahoo group. To learn more about this group please visit them online: http://tech.groups.yahoo.com/group/LightningProtection/

 

 

Click here to post a comment
[ View More Newsletters ] [ Send to a Friend ] [ Post Comments | View Comments | Notify Me When Comments Are Added ]

Copyright © Mike Holt Enterprises, Inc. All rights reserved.
This article is protected by United States copyright and other intellectual property laws and may not be
displayed or published on the internet without the prior written permission of Mike Holt Enterprises, Inc.

http://www.MikeHolt.com     1-888-NEC-CODE (1-888-632-2633)

Experiencing a Problem? Click Here

 
Comments
  • I tend to agree. Most of these noise/ground/wiring issues are due to "layers of messy civilization." I've lost count of "projects" where we finally just stopped, gutted it out, and re-did it, and lo and behold 3-4hrs of re-wiring solved weeks or months of on and off (mostly on) troubleshooting time.

    Put it in right the first time, or if you see a mess, clean it out and re-do it. It will always take less time to do it this way. Even if it doesn't cure the problem at hand, you now know it hasn't caused the problem at hand and won't cause other problems.

    Matt
    Reply to this comment

  • what is the correct way to ground a pex supplied whirlpool bathtub.....?

    gerard poster
    Reply to this comment

  • This article has nothing to do with constructing a Ground System but more to do with grounding and bonding as stated in the NEC and NFPA 780 Standard. Constructing a ground system is somewhat complicated in first you must know the soil resistance of the real estate that a ground system will be constructed. Once this is obtained by using the Megger 4 point measuring method and converting to Ohm-CM, you can calculate how many ground rods (electrodes) are to be used, spacing, depth, etc. Or, if ground rods cannot be used to provide the required (or desired low ohm resistance) then back fill methods or special designed chem-rods may have to be used, or both. All this is covered in many manuals including MIL Handbook 419A 1&2 for the Coast Guard Officer that wrote the article. Semper Paratus.

    Curtis Leary
    Reply to this comment

  • CSST bonding we have a way that is according to the NEC and now there are so many letters and e-mail from manufactures I would like to see something from the electrical side

    gerald wiedemann
    Reply to this comment

  • Why we need to isolate the grounding system for communication and then later we will bond it to the electrical system ground? Can we bond directly all communication equipment in the grounding grid?

    Mark
    Reply to this comment


Add Your Comments to this Newsletter
* Your Name:
   Your name will appear under your comments.

* Your Email:
   Your email address is not displayed.
* Comments:

This newsletter is closed to new comments.

Email Notification Options:
Notify me when a reply is posted to this comment
Notify me whenever a comment is posted to this newsletter